Aem 30-3438 Series 2 AEMnet Adapter Instrukcja Użytkownika Pobierz pdf

AEM Performance Electronics

2205 W 126

Street Unit A, Hawthorne, CA 90250

Phone: (310) 484-2322 Fax: (310) 484-0152

http://www.aemelectronics.com/

Instruction Part Number: 10-3438 Rev 1

 2011 AEM Performance Electronics, Inc.

Page 1

AEMnet

AEMnet is an open architecture software and hardware interface based on the CAN 2.0 specification,

which provides the ability for multiple AEMnet enabled devices to easily communicate with each other

through a single cable. The hardware connection is made through a Deutsch 4P DTM connector.

Devices connected to the AEMnet transmit data through this one connection. Once the AEMnet

adapter is installed, the Series 2 EMS will be able to send and receive data on the AEMnet.

Instructions for configuring the Series 2 EMS to output data are included in this manual. Instructions

on configuring the Series 2 EMS to receive data from other AEMnet enabled products are contained

in the individual product manuals. Upon completion of these instructions, the Series 2 EMS will be

configured to output data to an AQ1 Data Logger or other data receiving device.

The following AEM products are currently AEMnet enabled:

Series 2 Engine Management System

EMS-4 Universal Standalone Engine Management System

4-Channel Wideband UEGO Controller

AQ-1 Data Logger

Dyno Shaft On-Vehicle Dynamometer

Instruction Manual

P/N 30-3438 AEMnet Adapter Harness Installation

for Seri

es 2 EMS

6820 & 30

6821

1 2 3 4 5 6 7

Podsumowanie treści

Strona 1 - Instruction Manual

AEM Performance Electronics 2205 W 126th Street Unit A, Hawthorne, CA 90250 Phone: (310) 484-2322 Fax: (310) 484-0152 http://www.aemelectronics.com/

Strona 2 - AEMnet CONNECTORS

Page 2 AEMnet CONNECTORS The AEMnet has four wires, two are for communication (white pin 1 and green pin 2) and two are for powering (red pi

Strona 3

Page 3 REMOVE EXISTING WIRES FROM ECU PLUG(S) 1. Locate a small screwdriver (a precision 1mm wide flathead screwdriver is recommended) and

Strona 4

Page 4 2. Next remove the pin from the plastic connector by inserting the removal tool (factory recommended part available at Digikey, numb

Strona 5

Page 5 4. Make sure that the clip that holds the pin in the ECU connector is up so that it will clip properly into the connector. To instal

Strona 6 - CONFIGURING THE SERIES 2 EMS

Page 6 CONFIGURING THE SERIES 2 EMS The AEMnet data stream is compatible with version AEM25 01v23 firmware and later. To activate the AEMnet

Strona 7 - WARRANTY

Page 7 WARRANTY 12 MONTH LIMITED WARRANTY Advanced Engine Management Inc. warrants to the consumer that all AEM High Performanc

Komentarze do niniejszej Instrukcji

Brak uwag

Aem 30-3438 Series 2 AEMnet Adapter Instrukcja Użytkownika

Przeglądaj online lub pobierz Instrukcja Użytkownika dla Do samochodu Aem 30-3438 Series 2 AEMnet Adapter. AEM 30-3438 Series 2 AEMnet Adapter User Manual Instrukcja obsługi

Podsumowanie treści

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Do samochodu Aem 30-3438 Series 2 AEMnet Adapter